Cisco Security Advisory
Cisco IOS XE Software SD-Access Fabric Edge Node Denial of Service Vulnerability
CVSS:3.1/AV:N/AC:L/PR:N/UI:N/S:C/C:N/I:N/A:H/E:X/RL:X/RC:X
-
A vulnerability in the DHCP Snooping feature of Cisco IOS XE Software on Software-Defined Access (SD-Access) fabric edge nodes could allow an unauthenticated, remote attacker to cause high CPU utilization on an affected device, resulting in a denial of service (DoS) condition that requires a manual reload to recover.
This vulnerability is due to improper handling of IPv4 DHCP packets. An attacker could exploit this vulnerability by sending certain IPv4 DHCP packets to an affected device. A successful exploit could allow the attacker to cause the device to exhaust CPU resources and stop processing traffic, resulting in a DoS condition that requires a manual reload to recover.
Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.
This advisory is available at the following link:
https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-ios-xe-sda-edge-dos-MBcbG9kThis advisory is part of the September 2024 release of the Cisco IOS and IOS XE Software Security Advisory Bundled Publication. For a complete list of the advisories and links to them, see Cisco Event Response: September 2024 Semiannual Cisco IOS and IOS XE Software Security Advisory Bundled Publication.
-
Vulnerable Products
This vulnerability affects Cisco IOS XE Software if it is running on a device that is configured as an SD-Access fabric edge node and that has the DHCP Snooping feature enabled.
For information about which Cisco software releases are vulnerable, see the Fixed Software section of this advisory.
Determine the Device Configuration
To determine whether a device is configured as an SD-Access fabric edge node, use the following steps:
- In the GUI of Cisco Catalyst Center, formerly Cisco DNA Center, click the Menu icon.
- Choose Provision > SD Access > Fabric Sites and look for devices that are configured as fabric edge nodes.
Devices that are configured as fabric edge nodes will have DHCP Snooping enabled by default in Cisco Catalyst Center. DHCP Snooping must be enabled for a device to be affected by this vulnerability. To determine whether a device has DHCP Snooping enabled, use the show running-config | include ip dhcp snooping CLI command. If the command returns output, DHCP Snooping is enabled, as shown in the following example:
Switch# show running-config | include ip dhcp snooping
ip dhcp snooping
Switch#
Products Confirmed Not Vulnerable
Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.
Cisco has confirmed that this vulnerability does not affect the following Cisco products:
- IOS Software
- IOS XR Software
- Meraki products
- NX-OS Software
-
There are no workarounds that address this vulnerability.
-
Cisco has released free software updates that address the vulnerability described in this advisory. Customers with service contracts that entitle them to regular software updates should obtain security fixes through their usual update channels.
Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:
https://www.cisco.com/c/en/us/products/end-user-license-agreement.htmlAdditionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.
The Cisco Support and Downloads page on Cisco.com provides information about licensing and downloads. This page can also display customer device support coverage for customers who use the My Devices tool.
When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories page, to determine exposure and a complete upgrade solution.
In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.
Customers Without Service Contracts
Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html
Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.
Cisco IOS and IOS XE Software
To help customers determine their exposure to vulnerabilities in Cisco IOS and IOS XE Software, Cisco provides the Cisco Software Checker. This tool identifies any Cisco security advisories that impact a specific software release and the earliest release that fixes the vulnerabilities that are described in each advisory (“First Fixed”). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities that are described in all the advisories that the Software Checker identifies (“Combined First Fixed”).
To use the tool, go to the Cisco Software Checker page and follow the instructions. Alternatively, use the following form to determine whether a release is affected by any Cisco Security Advisory. To use the form, follow these steps:
- Choose which advisories the tool will search-only this advisory, only advisories with a Critical or High Security Impact Rating (SIR), or all advisories.
- Enter a release number-for example, 15.9(3)M2 or 17.3.3.
- Click Check.
-
The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.
-
This vulnerability was found during the resolution of a Cisco TAC support case.
-
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
-
Version Description Section Status Date 1.0 Initial public release. - Final 2024-SEP-25
-
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.